Mathey-dearman 6SA Saddle Machine Bedienungsanleitung

Po Box 472110, Tulsa, OK 74147 USA Toll Free: 800-725-7311 918-447-1288 office 918-447-0188 fax www.mathey.com 6SA Saddle Machine Part N

10 6.4 Adjust the oxygen and fuel gas regulator for the cutting tip size per the regulator manufacturer’s instructions. 6.5 Light the

11 Figure 5: CE 6SA Manual Machine Configuration Part #03-0106-000CE

12 Table 5: 6SA Machine – Manual Item # Part Description Part # Qty. 1 Saddle 03-0106-001 1 2 Cap Ring (Not Shown) 03-0106-003 1 3 Ring Gear 03-01

13 Figure 6: Single Bearing Bracket Assembly Part Number: 03-0105-005 Table 6: Right and Left Single Be

14 Figure 7: Double Bearing Bracket Assembly, Part # 03-0105-010 Table 7 – Double Bearing Bracket Assembly Part Identificatio

15 Table 8 – TROUBLESHOOTING – MANUAL MACHINE Symptom Possible Cause(s) Corrective Action Machine is cutting out of square Incorrect Spacer Bolt

16 7.1 Timing the Ring Gear to the Pinion Gears Adjusting of the timing requires the purchase of the Axle (Figure 5 item 4). Note: Redrill

17 7.1.20 Snug the 3/8-16 x 7/8” Hex Head Cap Screws (Figure 5 item 11) with a 9/16” wrench. 7.1.21 Move the Left Single Bearing Bracket (Figure 5

18 7.2 Installation of a New Drive Chains Installation of a new Top and Side Drive Chains (Figure 5 item 14 & 15) will also require the purchase

19 7.2.17 Move the Right Single Bearing Bracket (Figure 5 item 4) into position on the backside of Saddle (Figure 5 item 1), while rotating Pinion G

2 Table o of Contents Item Subject Page# 1.0 Safety

20 7.2.38 Snug the 3/8-16 x 7/8” Hex Head Cap Screws (Figure 4 item 11) with a 9/16” wrench. 7.2.39 Stretch the new Side Drive Chain (Figure 5 item

21 9.0 Machine Safety Users should follow these standard safety procedures in order to observe and prevent the safety of all employees using the Ove

22 12.0 Warranty If any merchandise sold hereunder (except merchandise manufactured by other persons or firms) by Mathey Dearman, Inc. (the “Company”

23

3 1.0 Safety Proper precautions should be taken when using this machine or any and all other heavy cutting and welding equipment. A little common s

4 2.0 General Information 2.1 The 6SA Saddle Machine is designed to rotate a 1 3/8”/35mm diameter 12” long oxy/fuel or plasma machine torch to cu

5 Figure 1: Spacer Configuration for 28”, 30” & 36” pipe Table 1 – Spacer Bolt Part Identification 4.0 Installation of Saddle Machine o

6 Picture 2 – Closing Boomer Figure 2: Boomer Assembly Part # 03-0106-010 Table 2 – Boomer Assembly Parts Identific

7 Figure 3: Torch Arm Part Number: 03-0101-001 Torch Carrier Assembly Part Number: 03-0100-002

8 Picture 4 – Installation of the Wing Nut 5.0.3 Remove the Clamp from the (Figure 3 Item 3) from the torch Carrier Assembly (Fig. 3, Ite

9 5.1.1 Thread the Extension Plate Spacers (Figure 5 item 21) on to the Threaded Studs (Figure 5 item 19) located on the Ring Gear (Figure 5 item 3)